用Snow Leopard需要開啟AHCI，希望在不重裝原來XP的提前下讓兩個系統并存，在網上找到一篇很完美的解決方案，做了一些修改以適應自己的TPower I45。有同樣需求的同學可以參考一下：
AHCI (Advanced Host Controller Interface) is present on newer Intel chipsets such as P965 (ICH8), P35 (ICH9), and P45(ICH10). AHCI mode is enabled in the BIOS and 3 settings are commonly available: IDE, AHCI, and RAID. The last two (AHCI and RAID) require a driver floppy and the F6 method when installing Windows XP otherwise the hard disks won't be detected.
AHCI mode brings 3 main advantages:
- Supports NCQ (Native Command Queuing) allowing SATA drives to accept more than one command at a time and dynamically reorder the commands for maximum efficiency.
- Supports hot plugging of devices
- Supports staggered spin ups of multiple hard drives at boot time
However, in the real world the performance difference isn't huge.
The problem is that if you installed Windows in IDE mode (ie you didn't use F6 and supply a driver disk), then simply changing the BIOS setting to AHCI mode and rebooting will cause Windows to fail and will require a repair install. Most people have been advising to reinstall Windows if you want AHCI enabled.
I managed to enable AHCI on Windows XP Professional for a BIOSTAR TPower I45 (ICH10R) without needing to reinstall. This should work on any P45 ICH10 based board:
1. Go to BIOSTAR official site or Intel's download centre and download the latest version of the Intel Matrix Storage Manager for your OS:
http://www.biostar-usa.com/app/en-us/t-power/driver.php?S_ID=365
http://downloadcenter.intel.com/
Keep this file as you'll need it again in step 4.
2. Run the installer with the -a switch to extract the files. This will NOT install the software, just extract the files. Follow the prompts as if you were installing the software:
The above should extract the files to \Program Files\Intel\Intel Matrix Storage Manager. There are two folders, \Drivers and \Drivers64 for 32-bit and 64-bit OS's, respectively.
Copy the file IaStor.sys from the Drivers folder to C:\Windows\System32\drivers\
3. copy the following registry file to your desktop (copy and paste into notepad) and save as ahci.reg
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Control\CriticalDeviceDatabase\pci#ven_8086&dev_3A22&cc_0106]
"Service"="iaStor"
"ClassGUID"="{4D36E96A-E325-11CE-BFC1-08002BE10318}"
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStor]
"Type"=dword:00000001
"Start"=dword:00000000
"Group"="SCSI miniport"
"ErrorControl"=dword:00000001
"ImagePath"="system32\\drivers\\iaStor.sys"
"tag"=dword:00000019
"DisplayName"="Intel AHCI Controller"
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStor\Parameters]
"queuePriorityEnable"=dword:00000000
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\iaStor\Enum]
"0"="PCI\\VEN_8086&DEV_3A22&SUBSYS_B0051458&REV_02\\3&13c0b0c5&0&FA"
"Count"=dword:00000001
"NextInstance"=dword:00000001
NOTE: Replace the red number with your device id!!!
4. Double check you've copied the IaStor.sys file as part of step 2. Now do the following:
- Run the ahci.reg file to add the entries into the registry
- Reboot the computer and enter the BIOS - DO NOT allow it to start Windows yet.
- Change the setting for the on board Intel controller to AHCI, save and exit BIOS
- Boot into Windows
When Windows loads it will detect a new hard disk - cancel the wizard for installing the new hardware and run the Intel driver installer you downloaded in step 1.
Reboot the system again and you're good to go.
原文連接：
http://forums.pcper.com/showthread.php?t=444831